Logo
AZO Disinfectant Wipes (200) – 70% IPA

AZO Disinfectant Wipes (200) – 70% IPA

Azo

Infection control and hygiene
  • Tested to relevant EN disinfectant efficacy standards (e.g. EN 14885 framework, including EN 1276, EN 13727, EN 13697, EN 13624, EN 14476, EN 14561, EN 14562 and EN 16615) for bactericidal, fungicidal, yeasticidal and virucidal activity (applies to the Azo™ 70% IPA range).
  • Compliant with EU Biocidal Products Regulation (BPR) 528/2012 for alcohol Based surface disinfectants (Azo™ 70% IPA wipes and sprays).
  • Manufactured under ISO 13485 and ISO 9001 quality management systems for medical products and devices (Azo™ range).
  • Made in Britain – manufactured in the UK by Vernacare.
  • Used widely in hospitals, laboratories and other healthcare settings as part of established infection prevention protocols.
Hard surface disinfectant wipes \u2013 70% isopropyl alcohol

Description

AZO Disinfectant Wipes (200) are strong, durable hard-surface wipes pre-saturated with a 70% isopropyl alcohol (IPA) solution. They provide rapid disinfection of non-porous surfaces and non-invasive medical equipment, killing key bacteria and other pathogens in under a minute, with typical validated contact times from 15 seconds. The quick-drying formulation leaves no residue and is widely used in clinical, dental, aesthetic and laboratory settings as part of routine infection prevention protocols.

Bnefits

  • Pre-saturated with 70% isopropyl alcohol for rapid, effective disinfection of hard surfaces and equipment.
  • Fast kill times, typically from 15 seconds, with bacteria killed in less than a minute.
  • Broad spectrum efficacy: bactericidal, virucidal, fungicidal and yeasticidal, effective against organisms such as MRSA, E. coli, Pseudomonas aeruginosa, Candida albicans and various enveloped viruses including coronaviruses.
  • Quick-drying, no-residue formulation, allowing surfaces and equipment to be used shortly after application.
  • Low-lint, strong and durable non-woven wipes that do not streak hard surfaces.
  • Convenient tub of 200 wipes for busy practices, reducing the risk of cross-contamination between patients.
  • BPR compliant and tested to relevant European EN standards for disinfectant efficacy.
  • Designed for professional clinical environments including hospitals, dental and aesthetic clinics, laboratories and care homes.

Indications

  • Rapid disinfection of hard, non-porous surfaces in healthcare and clinical environments (e.g. worktops, couches, trolleys, dental chairs).
  • Cleaning and disinfection of non-invasive medical equipment and devices, as part of infection prevention protocols.
  • Use in high-traffic professional environments such as hospitals, GP surgeries, dental and aesthetic clinics, laboratories, nursing homes and other healthcare settings.
  • Not intended for direct application to skin, open wounds or mucous membranes.

Composition

  • 70% v/v isopropyl alcohol (isopropanol) – active disinfectant component.
  • Approximately 30% v/v deionised water (typically 0.2 micron filtered) as diluent.
  • Non-woven wipe substrate (e.g. viscose rayon or similar strong, low-lint material).
  • May contain denatonium benzoate or similar bittering agent to discourage ingestion (formulation-dependent).
  • No added preservatives; designed to be low-smear and non-streaking on hard surfaces.

Formulation

  • Pre-impregnated disinfectant surface wipes.
  • Active solution: 70% v/v isopropyl alcohol in deionised water.
  • Wipe material: strong, low-lint non-woven substrate.
  • Typical wipe size: approximately 200 mm x 200 mm (standard tub format for Azo™ 70% IPA).
  • Quick-drying, non-residue formulation suitable for use between patients.

Packaging

  • Tub / canister containing 200 pre-saturated Azo™ 70% IPA disinfectant wipes.
  • Foil seal under the lid on many formats to reduce evaporation before first use.
  • Resealable snap-top lid to minimise drying out between uses.
  • Outer labelling with usage instructions, hazard pictograms and safety information.

Usage

  • For external use on hard, non-porous surfaces and non-invasive medical equipment only. Not for use on skin or mucous membranes.
  • Open the tub, remove a single wipe and immediately reseal the lid to prevent wipes from drying out.
  • Wipe the surface thoroughly, ensuring complete coverage; work from clean to dirty areas, using a single wipe in one direction where possible.
  • Ensure the surface remains visibly wet for the required contact time (typically from 15 seconds to 1 minute depending on organism and local protocol).
  • Allow the surface to air-dry completely; do not wipe dry with a separate cloth, as this may reduce efficacy.
  • Discard used wipes safely as clinical or general waste in accordance with local policies; do not flush.
  • Avoid use on incompatible surfaces that may be sensitive to alcohol (e.g. some plastics, rubber or painted finishes); test on a small inconspicuous area if necessary.
  • Keep away from sources of ignition and do not use on hot surfaces due to the flammability of 70% IPA.
  • Wash hands after prolonged or repeated use or wear appropriate gloves if required by local risk assessment.

Contraindications

  • Do not use on broken skin, open wounds or mucous membranes.
  • Not suitable as a hand or skin disinfectant unless specifically stated by the manufacturer for that purpose.
  • Avoid use on alcohol-sensitive surfaces or materials (e.g. some acrylics, varnished or painted surfaces, certain plastics and rubber components) without prior compatibility testing.
  • Do not use on or near ignition sources, open flames, very hot surfaces or where sparks may occur, due to the high flammability of 70% isopropyl alcohol.
  • Individuals with known hypersensitivity or allergy to isopropyl alcohol should avoid direct contact with the wipes or vapour.
  • Use with caution in poorly ventilated areas due to vapour build-up.

Adverse Effects

  • Skin: repeated or prolonged contact may cause dryness, irritation or cracking of the skin (defatting effect of alcohol); may rarely cause allergic skin reactions.
  • Eyes: causes serious eye irritation if splashed into the eyes, with symptoms such as redness, pain, watering and blurred vision.
  • Respiratory: inhalation of high concentrations of vapour may cause irritation of the respiratory tract, headache, dizziness or drowsiness.
  • Ingestion: accidental ingestion of the solution can cause irritation of the mouth, throat and gastrointestinal tract, nausea, vomiting and CNS effects typical of solvent ingestion.
  • General: product is highly flammable; exposure to sources of ignition may result in fire or explosion if sufficient vapour accumulates.
  • Most adverse effects are preventable by correct use, good ventilation, use of gloves where indicated and avoiding contact with eyes and skin.

Storage Conditions

  • Store in a cool, well-ventilated place away from direct sunlight and sources of heat or ignition.
  • Keep the tub tightly closed when not in use to prevent evaporation and drying out of wipes.
  • Store upright to minimise leakage of liquid within the canister.
  • Keep away from oxidising agents and incompatible materials.
  • Store out of the sight and reach of children.
  • Dispose of opened and unopened product according to local regulations once past its expiry date or if wipes have dried out.

Duration

Used as a single-use wipe for immediate surface disinfection; there is no fixed treatment duration. Surfaces should remain wet for the validated contact time (often 15 seconds to 1 minute) and allowed to air dry. Frequency of use depends on local infection control protocols and patient turnover.

Onset

Rapid onset; microbicidal activity typically begins within seconds. Validated contact times for many target organisms are from 15 seconds, with bacteria generally killed in under one minute when the surface remains wet.

Browse more Infection control and hygiene

Top Treatments

Top Cities in the UK