Replacement Veins for Injection Training Arm
Medisave
Clinical Training Models & SimulatorsIntravenous injection training arm spare part
Certifications
- Component of an educational training model; regulatory conformity for clinical use is not applicable as the product is not used on patients.
- Manufactured and supplied for medical and healthcare training environments under general product safety and quality management practices.
- Component of an educational training model; regulatory conformity for clinical use is not applicable as the product is not used on patients.
- Manufactured and supplied for medical and healthcare training environments under general product safety and quality management practices.
Intravenous injection training arm spare part
Description
Replacement Veins for Injection Training Arm (SKU AW7022) are spare synthetic vein lines designed specifically for use with the Injection Training Arm (product code AW7010). These substitute veins are installed inside the intravenous (IV) training arm to restore realistic venous access pathways for repeated practice of venepuncture, IV cannulation and infusion techniques. The product consists only of the replacement veins; the arm, skin shell, stand, simulated blood and accessories are not included.
Bnefits
- Purpose-made replacement vein set for the Injection Training Arm (AW7010), ensuring correct fit and function.
- Extends the service life of the IV training arm by allowing worn or punctured veins to be renewed without replacing the complete simulator.
- Helps maintain realistic blood-drawing and cannulation feedback for learners through intact, refillable vein lines.
- Supports ongoing skills training for venepuncture, IV insertion and infusion in nursing, medical and clinical education programmes.
- Cost-effective consumable component that can be replaced as needed after repeated needle punctures during training sessions.
Indications
- Replacement of damaged, leaking or heavily punctured veins in the Injection Training Arm (AW7010).
- Routine maintenance of IV injection training arms used in nursing schools, medical schools, simulation centres and hospital education departments.
- Support for training in venepuncture, IV cannulation and infusion setup on a dedicated arm model.
Composition
- Flexible synthetic tubing designed to simulate human veins (exact polymer not specified; typically non-biological training material).
- Pre-formed vein segments sized and routed to fit the internal structure of the Injection Training Arm (AW7010).
- Connections suitable for integration with the arm’s internal fluid system and simulated blood reservoir (where present).
Formulation
- Device type: Replacement synthetic veins for an IV injection training arm.
- Compatibility: Injection Training Arm – product code AW7010.
- Configuration: Multiple vein segments arranged to correspond with the arm model’s venous anatomy (e.g. forearm and hand veins), as supplied by the manufacturer.
- Intended fluid: Simulated blood or training fluid as recommended for the associated Injection Training Arm model.
Packaging
- Supplied as a set of replacement veins only; the Injection Training Arm (AW7010) and other components are not included.
- Packaged in protective wrapping or a small carton to prevent kinking or damage to the vein segments during transport.
- External labelling identifies the product as Replacement Veins for Injection Training Arm with reference to product code AW7010 and SKU AW7022.
Usage
- Ensure the Injection Training Arm (AW7010) is empty of training fluid and disconnected from any external tubing or reservoirs before replacing the veins.
- Open or disassemble the arm model according to the manufacturer’s instructions to gain access to the internal vein system.
- Carefully remove the existing vein tubing, noting the routing, orientation and connection points within the arm.
- Install the new replacement vein set following the same routing path, ensuring there are no sharp bends, kinks or twists.
- Reconnect the vein ends to the appropriate connectors, reservoirs and fluid lines as specified for the AW7010 arm.
- Refill the system with the recommended simulated blood or training fluid and purge air from the lines if required.
- Test the arm by performing a trial venepuncture or cannulation to confirm proper fluid flashback, flow and absence of leaks before use in training.
- After each training session, follow the Injection Training Arm’s cleaning and fluid-handling instructions to prolong the life of the new veins.
Contraindications
- Not intended for use in real patients or clinical procedures; for simulation and training use only.
- Do not use with fluids other than those recommended for the associated Injection Training Arm (e.g. avoid corrosive, sticky or particulate-containing liquids).
- Not compatible with other training arms or models unless explicitly specified by the manufacturer.
- Do not use if the replacement veins appear cracked, brittle, excessively kinked or otherwise damaged on arrival.
Adverse Effects
- No direct patient adverse effects, as the product is for simulation only and not used on humans.
- Improper installation may result in fluid leaks during training, potentially causing mess or contamination of the training area.
- Heavily punctured or degraded veins may lose realism, providing poor training feedback if not replaced in a timely manner.
Storage Conditions
- Store the replacement veins in their original packaging until installation to protect from dust and physical damage.
- Keep in a cool, dry place away from direct sunlight and sources of heat that may degrade synthetic materials.
- Avoid storing under heavy objects or in positions that cause prolonged sharp bends or compression of the tubing.
- Keep away from sharp tools or edges that could puncture or cut the vein segments.
